Wiring/en - Revision history

FuzzyBot: Importing a new version from external source

2017-07-22T03:36:14Z

Importing a new version from external source

2017-07-21T23:58:25Z

Importing a new version from external source

2017-07-21T23:58:25Z

Importing a new version from external source

2017-07-20T00:10:10Z

Importing a new version from external source

2017-07-19T08:55:27Z

Updating to match new version of source page

2017-07-19T06:48:55Z

Importing a new version from external source

2017-05-28T23:38:49Z

Importing a new version from external source

2017-03-11T03:56:39Z

Importing a new version from external source

2017-03-06T08:55:49Z

Updating to match new version of source page

2017-02-14T08:11:39Z

Importing a new version from external source

← Older revision		Revision as of 03:36, 22 July 2017
Line 252:		Line 252:


−	'''A special cable is needed to enable this communication. Signal wire (Orange) is connected to the AIL pin, while power wires (Red and Brown) are connected to the RUD port in the unit. For JETI REX receivers, end of the special cable is connected to the EX1 or EX2 (depending on the receiver configuration). For EX receivers, please use EXT port.'''	+	'''A special cable is needed to enable this communication.'''

	'''Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.'''		'''Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.'''

← Older revision		Revision as of 23:58, 21 July 2017
Line 252:		Line 252:


−	'''A special cable is needed to enable this communication.'''	+	'''A special cable is needed to enable this communication. Signal wire (Orange) is connected to the AIL pin, while power wires (Red and Brown) are connected to the RUD port in the unit. For JETI REX receivers, end of the special cable is connected to the EX1 or EX2 (depending on the receiver configuration). For EX receivers, please use EXT port.'''

	'''Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.'''		'''Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.'''

@@ Line 61: / Line 61: @@
+|
 |-
-|''CH0'' – Auxiliary (optional) servo
+|''CH0'' – Auxiliary/2nd Elevator (optional) servo
 |}

@@ Line 22: / Line 22: @@
 Neverthless you can also completely disable the unit' operation so that the control will be same as without the system. Then it can be anytime re-enabled during the flight.
+{| style="color:black; background-color:Lavender;width:75%;"
 {| style="color:black; background-color:Lavender; width:75%;"
 |<span style="color:red">'''Spirit'''</span>
@@ Line 59: / Line 70: @@
 == CONNECTION OF STANDARD RECEIVER (PWM) ==
 [[File:pwms.png|class=halfwidth|center]]
@@ Line 89: / Line 107: @@
 == CONNECTION OF SPEKTRUM DSM2/X SATELLITE ==
@@ Line 123: / Line 148: @@
 == CONNECTION OF FUTABA S-BUS RECEIVER ==
@@ Line 156: / Line 188: @@
 == CONNECTION OF PPM RECEIVER ==
@@ Line 184: / Line 223: @@
 == CONNECTION OF JETI EX BUS RECEIVER ==
@@ Line 213: / Line 259: @@
 == CONNECTION OF SRXL/SUMD RECEIVER ==

← Older revision		Revision as of 06:48, 19 July 2017
Line 243:		Line 243:

	== CONNECTOR ORIENTATION ==		== CONNECTOR ORIENTATION ==
		+
		+	=== μSpirit ===
		+	{{Quote\|Pin layout of the '''JST-ZH(R) connectors is different''' from standard Servo connectors. BROWN (Middle) wire is GND pin. ORANGE wire is SIGNAL pin. RED wire is +5V (BEC voltage). By using '''JST-Servo''' cables you can connect a classic Servos and all Spirit peripherals to the μSpirit even with Servo connectors.}}
		+
		+	[[File:uspirit-polarity.png\|280px\|center]]
		+
		+	=== Spirit and Spirit Pro ===

	All cables connected to the unit must be oriented so that the signal wire (Lightest color wire) is closer to the connector pin label, towards the center of the unit. This orients the negative (darkest color wire) toward the edge of the unit.		All cables connected to the unit must be oriented so that the signal wire (Lightest color wire) is closer to the connector pin label, towards the center of the unit. This orients the negative (darkest color wire) toward the edge of the unit.
		+
		+	[[File:spiritpro-polarity.png\|300px\|center]]

← Older revision	Revision as of 23:58, 21 July 2017
(No difference)

@@ Line 78: / Line 78: @@
 The unit is powered by two cables from the receiver connected to AUX and RUD positions. The Throttle cable should be connected to the receiver as well.
-The easiest way you can start is to connect RUD with Rudder output in the receiver. Then continue with AUX which should be connected to the Gyro Gain channel output. Next, connect the Aileron, Elevator channels and optionally Flaps channel. If you are not sure whether you have the correct output or not, you can plug in one servo and power the unit to verify that your connection is correct.  This can be repeated for each servo.  The diagnostics tab is very helpful too.
+The easiest way you can start is to connect RUD with Rudder output in the receiver. Then continue with AUX which should be connected to the Gyro Gain channel output. Next, connect the Aileron (AIL pin), Elevator (ELE pin) channels and optionally Flaps channel (PIT pin). If you are not sure whether you have the correct output or not, you can plug in one servo and power the unit to verify that your connection is correct.  This can be repeated for each servo.  The diagnostics tab is very helpful too.
 {{Info|'''Spirit Pro'''<br />The unit is able to control Bank Switching by 7th channel of the receiver.

@@ Line 232: / Line 232: @@
 Connection to a BEC is optional. For models with standard size servos it is recommended to use dual power supply cables due to the increased power consumption. That means besides the communication cable, an additional power supply cable should be connected to the AUX port.
 This protocol family can work with a wide range of receivers.
-Thus you can use Multiplex SRXL, BeastX SRXL, [[Graupner SUMD]], Jeti UDI, Spektrum SRXL and more.
+Thus you can use Multiplex SRXL, BeastX SRXL, Graupner SUMD, Jeti UDI, Spektrum SRXL and more.
 }}

@@ Line 229: / Line 229: @@
-{{Info|[[File:info.png|18px]]
+{{Info|[[File:info.png|18px|]]
 Connection to a BEC is optional. For models with standard size servos it is recommended to use dual power supply cables due to the increased power consumption. That means besides the communication cable, an additional power supply cable should be connected to the AUX port.
 This protocol family can work with a wide range of receivers.